适用于“一步酸溶法”生产氧化铝工艺中稀释料浆的高分子絮凝剂的合成

为达到"一步酸溶法"生产氧化铝工艺中稀释料浆在高温、高酸度工况下进行固液高效分离的目的,以丙烯酰胺(AM)与阳离子(DMDAAC)为共聚单体,通过水溶液聚合法合成了阳离子聚丙烯酰胺(CPAM)絮凝剂。以转化率和相对分子质量为目标,通过单因素分析法确定了最优的合成工艺条件,即反应温度30℃,单体总质量分数为30%,阳离子度5%,K2S2O8和NaHSO3质量分数均为0.005%,2,2′-偶氮二(2-脒基丙烷盐酸盐)(V50)质量分数为0.0025%,乙二胺四乙酸(EDTA)质量分数为0.05%的条件下,反应时间为6 h,获得相对分子质量为1.2×107溶解性能较好的阳离子型聚丙烯酰胺(CPAM)。     

Characterization of boron nitride nanosheets synthesized by boron-ammonia reaction

Boron nitride nanosheets (BNNS) with thickness 5–11 nm were successfully produced when pure boron powder (1–2 μm) interacted with ammonia gas in chemical vapour deposition set up. Under the optimized parameters, at 1200 °C and for uninterrupted 1 h of reaction duration, 2D BNNS with thickness of ca.11 nm were synthesized. BNNS were characterized by X-ray diffraction (XRD) for crystal structure, scanning electron microscopy for dimensions and morphology, energy dispersive X-ray analysis for chemical composition and Fourier transform infrared spectroscopy for sp² BN bond detection. The thickness of BNNS determined from both XRD data (using Scherrer equation) and atomic force microscopic analysis confirmed the stated product thickness. The BNNS obtained at 1200 °C had high crystallinity, purity and yield.     

基于STM32的开环霍尔电流传感器的温度补偿研究

研究了一种基于软件补偿结合恒流源补偿的改进温度补偿方法,应用单片机、恒流源、数字温度传感器、乘法器等硬件电路,对传统软件补偿进行了优化,补偿效果较传统恒流源补偿有了明显提升,“温漂”整体下降了约13.7%。在传统的温度补偿方法如热敏元件补偿、恒流源补偿、软件补偿等方式上做了补充,对于霍尔电流传感器精度的提升及实际生产需求的满足有重要意义。     

PVC地板行业研究现状及发展趋势

概述了国内外PVC地板行业的生产及应用现状,比较了几种地板材料的优缺点,介绍了PVC地板生产技术的研究进展情况,分析了国内PVC地板行业的发展趋势。     

双相区加速冷却处理对X80管线钢组织与性能的影响

采用双相区加速冷却法(加速冷却始冷温度为700 ℃)对X80管线钢进行热处理,获得了贝氏体和铁素体(B+F)双相组织。然后通过组织表征、力学性能测试以及在3.5wt%NaCl溶液中的耐蚀性进行研究。结果表明:热处理后获得的管线钢组织由板条状贝氏体、多边形铁素体及少量马氏体/奥氏体岛组成。与热处理前相比,(B+F)双相管线钢屈强比较低,为0.65,初始加工硬化指数为0.31,均匀伸长率达8.3%,塑性显著提升;双相组织中含有52.4%的铁素体,因而耐腐蚀性明显提高。通过双相区加速冷却法获得的(B+F)两相组织在塑变过程中发生协调变形,可以适应大变形的需求,同时耐蚀性优异,为大变形管线钢实际生产提供一定的借鉴。     

New ways to improve the damping properties in high‐performance thermoplastic vulcanizates

The incorporation of viscoelastic materials represents an effective strategy to reduce the vibratory level of structural components. Thermoplastic vulcanizates (TPVs) are a special type of viscoelastic material that combines the elastomeric properties of rubbers with the easy processing of thermoplastics. In the present work, we propose innovative ways to improve the damping properties of high‐performance TPVs by using rubbers with carboxylic functionalities. For that, TPVs from physical blends of carboxylated hydrogenated acrylonitrile butadiene rubber (XHNBR) and polyamide 6 (PA6) were prepared. The chain dynamics of different mixed crosslink systems containing peroxide, metal oxides and hindered phenolic antioxidants were investigated in order to find the most suitable strategy to design a high‐performance TPV system with upgraded damping properties. The results indicate that the damping performance of the TPV system can be tailored by controlling the type and magnitude of the bonding interactions between the mixed crosslink system and the XHNBR rubber phase. Therefore, this study demonstrates the potential of TPV systems containing carboxylic rubbers as high‐performance damping materials. © 2020 Society of Chemical Industry     

朝凯煤矿露天台阶爆破装药结构优化应用研究

本文以神达朝凯煤矿正在开采的台阶为工程背景,针对该矿在台阶爆破过程中存在着大块率高、根底多的现象,通过改变装药结构的方式对爆破参数进行优化。实践证明,优化后大块率和根底问题的治理效果明显。     

Effect of thermomechanical processing on microstructure and mechanical properties of CoCrFeNiMn high entropy alloy

The CoCrFeNiMn high entropy alloy was produced by homogenization, cold rolling and recrystallization. The effects of thermomechanical processing on microstructures and tensile properties at different temperatures were investigated using X-ray diffractometry (XRD), optical microscopy (OM), scanning electron microscopy (SEM) and multi-functional testing machine. The results show that dendritic structures in cast alloy evolve into equiaxed grains after being recrystallized, with single face-centered cubic (FCC) phase detected. The most refined alloys, stemming from the highest rolling ratio (40%), exhibit the highest strength due to the grain boundary strengthening, while the variation of elongation with temperature shows a concave feature. For the coarse-grained alloys, both the ductility and work hardening ability decrease monotonically with increasing temperature. Serrated flow observed at intermediate temperatures is attributed to the effective pinning of dislocations, which manifests the occurrence of dynamic strain hardening and results in the deterioration in ductility. Besides, dimples on the fracture surfaces indicate the typical ductile rupture mode.     

Optimization of three-dimensional boiling enhancement structure at evaporation surface for high power light emitting diode

A theoretical model of phase change heat sink was established in terms of thermal resistance network. The influence of different parameters on the thermal resistance was analyzed and the crucial impact factors were determined. Subsequently, the forming methods including ploughing–extrusion and stamping method of boiling enhancement structure at evaporation surface were investigated, upon which three-dimensional microgroove structure was fabricated to improve the efficiency of evaporation. Moreover, the crucial parameters related to the fabrication of miniaturized phase change heat sink were optimized. The heat transfer performance of the heat sink was tested. Results show that the developed phase change heat sink has excellent heat transfer performance and is suitable for high power LED applications.     

Linear correlation between pH value of stimulated beef and electrical current intensity

The aim of the present study was to determine mathematical relationships between pH changes in beef 24 h post-slaughter and changes in the intensity of electrical current flowing through bull and heifer carcasses during high-voltage electrical stimulation. The electrical stimulation was applied 40 min postmortem for 120 s. The pH values of m. longissimus thoracis et lumborum were analyzed in the function of electrical current intensity changes and its change during electrical stimulation. Mathematical linear correlations of the y = ax ± b type were demonstrated between pH values at 2, 6, and 24 h postmortem and the initial (I_i) and ultimate (I_u) electrical current intensity values, the difference between them and the initial pH values determined before electrical stimulation. High multiple correlation coefficients (R² = 0.416, α ≤ 0.001) between I_u and pH values 24 h post-slaughter enabled concluding that there is a possibility to predict a pH value of stimulated carcass with high accuracy, and thus also beef quality, based merely on the ultimate electrical current intensity values.